AIX Configuration and Process Codes

 

 LED Value Description 
_____ ______________________________________________________________________ 

000 – 049 (Reserved)

050 - 099    Reserved for Service Processor usage.


Dump Codes (0c1 -0cc)

0c1  Dump Failed Due to an I/O Error
0c2  Dump, requested by user, is started.
0c3  Dump is inhibited
0c4  Dump Device Not Large Enough
0c5  Dump Did Not Start or Dump Crashed.
0c6  Dumping to Secondary Dump Device
0c8  Dump function is disabled.
0c9  A dump is in progress
0cc  Unknown Dump Failure (prior to rel 42G)/Dumping to secondary dump device.

Crash Codes

Note: Crash Codes are part of a flashing "888" message of the type "888 102 xxx yyy" where the "xxx" is the crash code and the "yyy" is the dump status (code).

000  Unexpected system interrupt.
200  Machine check because of a memory bus error.
201  Machine check because of a memory timeout.
202  Machine check because of a memory card failure.
203  Machine check because of a out of range address.
204  Machine check because of an attempt to write to ROS (Read Only Storage).
205  Machine check because of an uncorrectable address parity.
206  Machine check because of an uncorrectable ECC error.
207  Machine check because of an unidentified error.
208  Machine check due to an L2 cache Uncorrectable ECC.
2E6  The PCI Differential Ultra SCSI adapter or the Universal PCI Differential
2E7  Configuration method unable to determine if the SCSI adapter type is
     SE or DE type.
300  Data storage interrupt from the processor.
32x  Data storage interrupt because of an I/O exception from the IOCC.
38x  Data storage interrupt because of an I/O exception from the SLA.
400  Instruction storage interrupt.
558  There is not enough memory to continue the IPL.
600  Alignment Interrupt (Replaces former 600 crash code
605  AIX has crashed because the Portability Assist Layer (PAL) for
     this machine type has detected a problem.
700  Program Interrupt (invalid instructions, traps, and panics).
800  Floating Point function not available.

BIST Codes (100 – 199)

100  BIST completed successfully  control was passed to ROS.
101  Initial BIST started following RESET.
102  BIST started following Power-On-RESET.
103  BIST could not determine the system model number.
104  BIST could not find the CBA.
105  BIST could not read from the OCS EPROM.
106  BIST detected a module failure.
111  BIST detected a module failure.
112  Checkstop occurred during BIST and results could not be logged out.
113  The BIST checkstop count was greater than 1.
120  BIST started CRC check on 8752 EPROM
121  BIST detected a bad CRC on the OCS EPROM.
122  BIST started CRC check on the OCS EPROM.
123  BIST detected a bad CRC on the OCS NVRAM.
124  BIST started CRC check on the OCS NVRAM.
125  BIST detected a bad CRC on the time of day NVRAM.
126  BIST started CRC check on the time of day NVRAM.
127  BIST detected a bad CRC on the 8752 EPROM
130  BIST presence test started.
140  BIST Failed.
142  BIST Failed.
143  Invalid Memory Configuration.
144  BIST Failed.
151  BIST started AIPGM test code.
152  BIST started DCLST test code.
153  BIST started ACLST test code.
154  BIST started AST test code.
160  Bad EPOW signal/Power status signal
180  BIST logout failed.
182  BIST: COP bus not responding.
185  Checkstop occurred during BIST.
186  System generated checkstop (systems without BIST)
187  Graphics generated checkstop
195  BIST logout completed.

POST Codes (200 to 299)

200  Boot attempted with keylock in the secure position.
201  Checkstop occurred during boot.
202  Unexpected machine check interrupt.
203  Unexpected data storage interrupt.
204  Unexpected instruction storage interrupt.
205  Unexpected external interrupt..
206  Unexpected alignment interrupt.
207  Unexpected program interrupt.
208  Unexpected floating point unavailable.
209  Unexpected SVC interrupt.
20c  Error detected in L2 cache (when LED persists for 5 seconds).
210  Unexpected SVC 1000 interrupt.
211  ROS CRC miscompare during boot.
212  Processor Planar Bad FATAL
213  Memory Card failure or Processor Planar Bad.
214  Power status register failed
215  A low voltage condition is present
216  ROS code being uncompressed into memory.
217  End of boot list encountered.
218  RAM POST testing for 2 MB of good memory
219  RAM POST bit map being generated.
21c  L2 Cache not detected as part of systems configuration( 2 second dur.
220  IPL Control Block being initialized.
221  NVRAM CRC comparison error during boot in Normal Mode.
222  Attempting Normal boot from NVRAM Boot List from SIO attached devices
223  Attempting Normal boot from NVRAM Boot List from SCSI attached devices
224  Attempting Normal Mode Boot from 9333 subsytem device
225  Attempting Normal Mode boot from from 7012 DBA Disk
226  Attempting Normal Mode boot from Ethernet
227  Attempting Normal Mode boot from Token Ring
228  Attempting Normal boot using expansion code in NVRAM.
229  Attempting Normal Mode boot but list is empty or no devices are available.
22c  Attempting a normal mode IPL from FDDI specified in NVRAM IPL device list.
230  Attempting Normal boot from ROM Boot List.
231  Attempting Normal Mode boot from Ethernet
232  Attempting Normal Mode boot from SIO attached devices
233  Attempting Normal Mode boot from SCSI attached devices
234  Attempting Normal Mode boot from 9333 subsytem device
235  Attempting Normal Mode boot from from 7012 DBA Disk
236  Attempting Normal Mode boot from Ethernet
237  Attempting Normal Mode boot from Token Ring
238  Attempting a Normal-mode restart from Token Ring specified by the user.
239  System failed to boot from the device specified by the user.
23c  Attempting a normal mode IPL from FDDI specified in IPL ROM device list.
240  Attempting a Service boot from ROM boot list.
241  Attempting a Normal boot from devices specified in NVRAM boot list
242  Attempting Service Mode boot from SIO attached devices
243  Attempting Service Mode boot from SCSI attached devices
244  Attempting Service Mode boot from 9333 subsytem device
245  Attempting Service Mode boot from from 7012 DBA Disk
246  Attempting Service Mode boot from Ethernet
247  Attempting Service Mode boot from Token Ring
248  Attempting Service boot using expansion code in NVRAM.
249  Attempting Service Mode boot from the NVRAM IPL device list.
24c  Attempting a service mode IPL from FDDI specified in NVRAM IPL device list.
250  Attempting a Service boot from adapter feature ROM.
251  Attempting Service Mode boot from Ethernet
252  Attempting Service Mode boot from SIO attached devices
253  Attempting Service Mode boot from SCSI attached devices
254  Attempting Service Mode boot from 9333 subsytem device
255  Attempting Service Mode boot from from 7012 DBA Disk
256  Attempting Service Mode boot from Ethernet
257  Attempting Service Mode boot from Token Ring
258  Attempting Service boot from Token Ring specified by user.
259  Attempting a service mode IPL from FDDI specified by the operator.
25c  Attempting a service mode IPL from FDDI specified in IPL ROM device list.
260  ROM attempting to display information on the native console.
261  ROM did not find a native display adapter and information will be displayed on the TTY console.
262  ROM did not detect a keyboard while attempting to display information.
263  Attempting a Normal-mode restart from adapter feature ROM specified in NVRAM device list.
269  Stalled State - cannot boot system end of boot list reached
270  Durandoak Ethernet Adapter (LCE) POST executing.
271  Mouse device and adapter POST executing.
272  Tablet adapter POST executing.
276  San Remo Ethernet adapter POST executing.
277  Auto Token-Ring LANstreamer MC 32 Adapter POST.
278  Video ROM SCAN POST executing.
279  FDDI POST.
280  3COM Ethernet POST
281  Keyboard POST executing.
282  Parallel port POST executing.
283  Serial port POST executing.
284  POWER Gt1 graphics adapter POST executing.
285  POWER Gt3 graphics adapter POST executing.
286  Token Ring adapter POST executing.
287  Ethernet adapter POST executing.
288  Adapter card slots being queried.
289  POWER Gt0 graphics adapter POST executing.
290  Testing I/O planar
291  Standard I/O planar being tested.
292  SCSI or SSA adapter POST executing.
293  Bus attached disk POST executing.
294  TCW SIMM in slot J being tested.
295  Color graphics display adapter POST executing.
296  Family 2 feature adapter ROM POST executing.
297  System model number could not be determined.
298  Attempting a warm IPL.
299  Boot ROM passed control to loaded code.

IPL ROS Flash EPROM Codes (300 -325)

301  Flash Utility ROM test failed or checkstop occurred (irrecoverable).
302  Flash Utility ROM: User prompt, move key to service position in
     order to perform an optional Flash Update. LED 302 will only appear
     if the Key switch is in secure.  This signals the user that a Flash
     Update may be initiated by moving the key switch to service. If the
     key is moved to service then LED 303 will be displayed which signals
     the user to press the reset button to select optional Flash Update.
303  Flash Utility ROM: User prompt, press reset button in order to
     perform an optional Flash Update. LED 302 will only appear if the
     Key switch is in secure.  This signals the user that a Flash Update
     may be initiated by moving the key switch to service.  If the key is
     moved to service then LED 303 will be displayed which signals the
     user to press the reset button to select optional Flash Update.
304  Flash Utility ROM IOCC POST Error (irrecoverable).
305  Flash Utility ROM Standard I/O POST running.
306  Flash Utility ROM is attempting IPL from Flash Update media device.
307  Flash Utility ROM system model number does not compare between OCS
     and ROM (irrecoverable).
308  Flash Utility ROM: IOCC bad TCW SIMM in being tested.
309  Flash Utility ROM passed control to a Flash Update Boot Image.
311  Flash Utility ROM CRC comparison error (irrecoverable).
312  Flash Utility ROM RAM POST memory configuration error or no memory
     found (irrecoverable).
313  Flash Utility ROM RAM POST failure (irrecoverable).
314  Flash Utility ROM Power status register failed (irrecoverable).
315  Flash Utility ROM detected a low voltage condition.
318  Flash Utility ROM RAM POST is looking for good memory.
319  Flash Utility ROM RAM POST bit map is  being generated.
322  CRC error on media Flash Image.  No Flash Update performed.
323  Current Flash Image is being erased.
324  CRC error on new Flash Image after Update was performed. (Flash
     Image is corrupted).
325  Flash Update successful and complete.

326 – 3CC (Reserved)

AIX Event Indicators


Configuration Program Indicators

2E6  Ultra/Wide Differential SCSI adapter being configured
2E7  Config method unable to determine if SCSI adapter type SE or DE type
40c  Victory Mini-Support Processor being configured
41c  Victory Plug In Adapter Support Processor being Configured.
42c  Waiting for Interactive Maintenance Analysis Procedures (IMAPS)request.
43c  Configuring Interactive Maintenance Analysis Procedures (IMAPS) connection.
4c0  4c5 Reserved for Rochester AS4D AIX IOP device driver usage.
440  9.1GB SE Ultra drive (Mako 68 pin)
441  18.2GB SE Ultra drive (Mako 68 pin)
442  9.1GB LVD Ultra drive (Neptune 80 pin)
443  18.2GB LVD Ultra drive (Neptune 80 pin)
444  Cost-reduced Hermosa WAN adapter
447  Emulex LP9000 (Centaur) PCI 64 FCS adapter (Flipper64)
500  Querying Standard I/O.
501  Querying card in slot 1.
502  Querying card in slot 2.
503  Querying card in slot 3.
504  Querying card in slot 4.
505  Querying card in slot 5.
506  Querying card in slot 6.
507  Querying card in slot 7.
508  Querying card in slot 8.
509  Configuring ATL L500 library (tower configuration) -- IBM machine 7337-410
510  Starting device configuration.
511  Device configuration completed.
512  Restoring device configuration files from media.
513  Restoring basic operating system installation files from media.
516  Contacting server during network boot
517  Mounting client remote file system during network IPL.
518  Remote mount of the root and /usr filesystems failed during network
     boot.
519  Configuring ATL L500 library (rack configuration) ---  IBM machine 7337-411
520  Bbus configuration running.
521  /etc/init invoked cfgmgr with invalid options; /etc/init has
     been corrupted or incorrectly modified (irrecoverable error).
522  The configuration manager has been invoked with conflicting
     options (irrecoverable error).
523  The configuration manager is unable to access the ODM database
     (irrecoverable error).
524  The configuration manager is unable to access the config rules
     object in the ODM database (irrecoverable error).
525  The configuration manager is unable to get data from a
     customized device object in the ODM database (irrecoverable error).
526  The configuration manager is unable to get data from a
     customized device driver objet in the ODM database (irrecoverable
     error).
527  The configuration manager was invoked with the phase 1 flag;
     running phase 1 flag; running phase 1 at this point is not
     permitted (irrecoverable error).
528  The configuration manager cannot find sequence rule, or no program
     was specified in the ODM database (irrecoverable error).
529  The configuration manager is unable to update ODM data
     (irrecoverable error).
530  The program "savebase" returned an error.
531  The configuration manager is unable to access PdAt object class
     (irrecoverable error)
532  There is not enough memory to continue (malloc failure);
     irrecoverable error.
533  The configuration manager could not find a configure method for
     a device.
534  The configuration manager is unable to acquire database lock.
     irrecoverable error.
536  The configuration manager encountered more than one sequence rule
     specified in the same phase. (irrecoverable error).
537  The configuration manager encountered an error when invoking the
     program in the sequence rule.
538  The configuration manager is going to invoke a configuration
     method.
539  The configuration method has terminated, and control has returned
     to the configuration manager.
540  IP Security (IPSec) kernel extensions being configured during IPL.
541  Configuring ATL L500 DLT7000 drive sled assembly
541  A DLT tape device is being configured
542  Configuring ATL L200 autoloader -- IBM machine 7205-342
543  Configuring ATL L200 DLT7000 drive sled assembly
544  ECP peripheral configure method executing.
545  Parallel port ECP device driver being configured.
546  IPL cannot continue due to error in customised data base.
547  Rebooting after error recovery (LED 546 preceded this LED)
548  Restbase failure.
549  Console could not be configured for the "Copy a System Dump Menu.
550  ATM LAN Emulation device driver being configured.
551  IPL Varyon is running
552  IPL Varyon failed.
553  IPL phase 1 is complete.
554  The boot device could not be opened or read,
     or unable to define NFS swap device during network boot.
555  ODM error when trying to varyon the rootvg, or unable
     to create an NFS swap device during network boot.
556  Logical Volume Manager encountered error during IPL varyon.
557  The root filesystem will not mount.
558  There is not enough memory to continue the system IPL.
559  Less than 2MB of good memory are available to load the AIX kernel.
560  Unsupported Monitor attached to display adapter.
561  Configuring Target Mode SSA device software.
562  Configuring HIPPI network layer.
565  Configuring the MWAVE subsystem.
566  Configuring Namkan twinax commo card (5250 emulation)
567  Configuring HIPPI device driver (fpdev)
568  Configuring HIPPI device driver (fphip)
569  FCS SCSI Protocol device is being configured
570  Virtual SCSI devices being configured.
571  HIPPI common function device driver being configured.
572  HIPPI IPI-3 master transport driver being configured.
573  HIPPI IPI-3 slave transport driver being configured.
574  HIPPI IPI-3 transport services user interface device driver being configured.
575  IBM 9570 RAID 3 disk array device driver being configured.
576  Vendor Async device driver configuration.
576  Generic async device driver being configured.
577  Generic SCSI device driver being configured.
578  Generic commo device driver being configured.
579  Device driver being configured for a generic device.
580  HIPPI TCPIP network interface driver being configured.
577  Vendor SCSI device driver configuration.
578  Vendor Commo device driver configuration.
579  Configuring a generic vendor device driver configuration.
580  HIPPI TCPIP network interface driver being configured.
581  Configuring TCP/IP.
582  Configuring token ring data link control
583  Configuring ethernet data link control
584  Configuring IEEE ethernet data link control
585  Configuring SDLC MPQP data link control
586  Configuring QLLC X.25 data link control
587  Configuring NETBIOS
588  Configuring a Bisync Read-Write (BSCRW).
589  SCSI target mode device being configured.
590  Diskless remote paging device being configured.
591  Configuring an LVM device driver.
592  Configuring an HFT device driver.
593  Configuring SNA Device Drivers or Configuring LFT.
594  Asynchronous I/O being defined or configured.
595  X.31 pseudo device being configured.
596  SNA DLC/LAPE pseudo device being configured.
597  OCS Software being configured.
598  OCS hosts being configured during system reboot.
599  Configuring FDDI data link control.
59c  Tarpon/Shark storage subsystem device driver configuration.
5c0  Streams based hardware driver being configured.
5c1  Streams based X.25 protocol stack being configured.
5c2  Streams based X.25 COMIO emulator driver being configured.
5c3  Streams based X.25 TCP/IP interface driver being configured.
5c4  FCS adapter device driver being configured.
5c5  Pseudo device for IP mapping Network device driver for FCS being configured.
5c5  SCB network device driver for FCS is being configured.
5c6  AIX SNA Channel being installed and configured.
600  Starting network boot portion of /sbin/rc.boot
602  Configuring network parent devices.
603  /usr/lib/methods/defsys,  /usr/lib/methods/cfgsys, or
     /usr/lib/methods/cfgbus failed.
604  Configuring physical network boot device.
605  Configuration of physical network boot device failed.
606  Running /usr/sbin/ifconfig on logical network boot device.
607  /usr/sbin/ifconfig failed.
608  Attempting to retrieve the client.info file with tftp.
     Note that a flashing 608 indicates multiple attempt(s) to
     retrieve the client_info file are occurring.
609  The client.info file does not exist or it is zero length.
60B  18.2GB 68-pin LVD SCSI Disk Drive being configured
60C  Lochmere 1.4 GB IDE disk drive being configured.
610  Attempting remote mount of NFS file system
611  Remote mount of the NFS filesystem failed.
612  Accessing remote files; unconfiguring network boot device.
614  Configuring local paging devices.
615  Configuring of a local paging device failed.
616  Converting from diskette to dataless configuration.
617  Diskless to dataless configuration failed.
61c  Lochmere 2.1 GB IDE disk drive being configured.
618  Configuring remote (NFS) paging devices.
619  Configuration of a remote (NFS) paging device failed.
61B  36.4GB 80-pin LVD SCSI Disk Drive being configured.
61D  36.4GB 80-pin LVD SCSI Disk Drive being configured.
61E  18.2GB 68-pin LVD SCSI Disk Drive being configured.
620  Updating special device files and ODM in permanent filesystem with
     data from boot RAM filesystem.
621  9.1 GB LVD 80-pin SCSI Drive being configured.
622  Boot process configuring for operating system installation.
625  Creating directory for local NIM mount points.
626  OEM FC SCSI Disk being configured.
627  FC SCSD SCSI Disk being configured.
628  SCSI SCSD FC CDROM Drive being configured.
629  OEM SCSI FC CDROM Drive being configured.
62c  Lochmere 3.0 GB IDE disk drive being configured.
62D  9.1GB 68-pin LVD SCSI Disk Drive being configured.
62E  9.1GB 68-pin LVD SCSI Disk Drive being configured.
630  SCSD FC SCSI Read/Write Optical Drive being configured.
631  OEM FC SCSI Read/Write Optical Drive being configured.
632  25 Mbs Charm 1.5 ATM adapter being configured.
633  155 Mbs Charm 2.1 UTP ATM adapter being configured.
634  155 Mbs Charm 2.1 MMF ATM adapter being configured.
635  155 Mbs Charm 2.1 SMF ATM adapter being configured.
636  622 Mbs Charm 2.5 BigBend ATM adapter being configured
636  TURBOWAYS 622 Mbps PCI MMF ATM Adapter.
637  Aladdin Dual Channel PCI-2 Ultra2 SCSI Adapter being configured.
638  4.5GB Ultra SCSI Single Ended Disk Drive being configured.
639  9.1GB 10K RPM Ultra SCSI Disk Drive (68-pin) being configured.
63A  See 62D.
63B  9.1GB 80-pin LVD SCSI Disk Drive being configured.
63C  See 60B.
63D  18.2GB 80-pin LVD SCSI Disk Drive being configured.
63E  36.4GB 68-pin LVD SCSI Disk Drive being configured.
63F  See 61B.
640  9.1GB 10K RPM Ultra SCSI Disk Drive (80-pin).
641  Draco 9.1 GB 80-pin LVD Ultra 2 SCSI disk being configured.
642  Draco 4.5 GB LVD 80-pin SCA-2 connector SCSI Disk being configured
643  Hammerhead 18.2 GB LVD 80-pin SCA-2 connector SCSI Disk being configured
644  Swordfish 36.4 GB LVD 80-pin SCA-2 connector SCSI Disk being configured
646  High-Speed Token-Ring PCI Adapter being configured.
649  8X Optical Disk drive being configured (Pirahna Tape Library)
64A  See 62E.
64B  9.1GB 80-pin LVD SCSI Disk Drive being configured.
64C  See 61E.
64D  18.2 GB LVD 80-pin Drive/Carrier being configured.
64E  36.4GB 68-pin LVD SCSI Disk Drive being configured.
64F  See 61D.
650  IBM SCSD disk drive being configured.
651  Reserved (Diagnostics)
652  Reserved (Diagnostics)
653  18.2GB Ultra-SCSI 16-bit Disk Drive being configured.
654  Sailfin Jr. 4.5 GB 68 Pin SCSI SE drive being configured.
655  GXT130P (Maui) Graphics adapter being configured.
656  Polar 3 1/4 inch SCSI tape drive being configured.
657  GXT2000P Mirage graphics adapter being configured.
658  Dolphin 2102 disk array controller configuration.
658  PCI Fibre Channel Disk Subsystem Controller being identified or configured.
659  Dolphin 2102 disk array router configuration.
659  2102 Fibre Channel Disk Subsystem Controller Drawer being identified or
     configured.
660  Dolphin 2102 Fibre Channel Disk Array being identified or configured.
661  OEM IDE Tape Drive
661  USB host controller configuration.
662  Ultra2 Integrated SCSI controller
662  Smbios 895 based SCSI adapter configuration.
663  The ARTIC960RxD Digital Trunk Quad PCI Adapter or the ARTIC960RxF
     Digital Trunk Resource Adapter being configured.
664  Brighton 32X SCSI CDROM drive configuration.
665  Sailfin 9.1 GB 80 pin LVD SCSI disk drive configuration.
666  Marlin 18.2 GB 80 pin LVD SCSI disk drive configuration.
667  PCI 3-Channel Ultra2 Clarinet SCSI RAID Adapter being configured.
668  25 Mbs MCA ATM adapter configuration.
669  PCI Gigabit Ethernet Adapter Galaxy being configured.
66C  10/100/1000 Base-T EthernetPCI Adapter.
66D  PCI 4-Channel Ultra-3 SCSI RAID Adapter.
66E  4.7 GB DVD-RAM drive
670  Marlin 18.2 GB SCSI 80 Pin SCA driver configuration.
671  Sailfin 9.1 GB SCSI 80 Pin SCA driver configuration.
672  Sailfin 9.1 GB SCSI differential drive configuration.
673  Marlin 18.1 GB SCSI differential drive configuration.
674  ESCON ® Channel PCI Adapter being configured.
675  ARTIC960Hx PCI adapter being configured.
676  ARTIC960Rp PCI adapter being configured.
677  PCI 32-bit Fibre Channel Arbitrated Loop Adapter being configured.
677  Emulex LP7000 PCI 32 FCS adapter(firefly/superfly+) being configured.
678  Cadenza 12 GB 4mm tape drive being configured.
679  Draco 4.5 GB SCSI disk drive being configured.
67a  Emulex LP9000 (Centaur) PCI 64 FCS adapter (Flipper64)
67B  PCI Cryptographic Coprocessor being configured.
680  Supermint MCA Graphics Adapter being configured.
681  Sailfin 9.1 GB Single Ended SCSI disk Drive being configured.
682  20x (MAX) SCSI-2 CD-ROM Drive being configured.
682  ALTA 12X - 20X CDROM drive being configured.
683  IBM 2105 Device being configured.
684  RS 422 Concentrator being configured.
685  Sagebrush Graphics adapter being configured.
686  Medina 8-Port Async PCI adapter being configured.
687  Trinity 128-Port Async adapter being configured.
688  SCSI MC-Disk PCMCIA Card reader being configured.
689  Scorpion 4.5GB Ultra SCSI Single Ended Disk Drive being configured.
68C  20 GB 4-mm Tape Drive being configured.
68E  POWER GXT6000P PCI Graphics Adapter.
690  Scorpion 9.1GB Ultra SCSI Single Ended Disk Drive being configured.
691  Turboway 25 Mbs PCI ATM adapter being configured.
692  7205-311 30 GB DLT Tape (Bullhead) drive being configure.
693  ISDN PCI Basic Rate adapter being configured.
694  ISDN MCA Basic Rate adapter being configured.
695  X.25 PCI Coprocessor adapter being configured.
696  Lumbee (Meerkat) 8 MB SM fiber adapter being configured.
697  Lumbee (Gemini- lite) 1 MB MM fiber adapter being configured.
698  Lumbee (Orbitor) 1 MB UTP fiber adapter being configured.
699  Candlestick Park (10/100 Mbs Ethernet adapter being configured.
69b  64-bit/66MHz PCI ATM 155 MMF PCI adapter being configured.
69d  64-bit/66MHz PCI ATM 155 UTP PCI adapter being configured.
6c8  Lochmere Display device driver being configured.
6cc  SSA disk drive being configured.
700  Starfire 1.1 GB 8 Bit SCSI Disk being configured.
701  Starfire 1.1 GB 16 Bit SCSI Disk being configured.
702  Starfire 1.1 GB 16 Bit Differential Disk being configured.
703  Starfire 2.2 GB 8 Bit SCSI Disk being configured.
704  Starfire 2.2 GB 16 Bit SCSI Disk being configured.
705  The configuration method for the 2.2GB 16-bit differential SCSI
     disk drive is being run. If a irrecoverable error occurs, the
     system halts.
705  Starfire 2.2 GB 16 Bit Differential SCSI Diff Disk being configured.
706  Starfire 4.5 GB 16 Bit SCSI Disk being configured.
707  Starfire 4.5 GB 16 Bit Differential Disk being configured.
708  L2 Cache being configured.
709  Frio ISA 128 port async adapter being configured.
70c  270 MB SCSI disk drive (Sandalfoot - Satsuma 1) being configured.
710  POWER GXT150M Neptune graphics adapter being identified/configured.
711  Unknown adapter being identified or configured.
712  Graphics slot bus configuration is executing.
713  Artic 960 adapter being identified/configured
714  Sunrise Video Capture Adapter being identified/configured
715  Fox Club Ultimedia Services audio adapter is being configured. This LED
     displays briefly on the panel.
716  Pegasus system memory
717  Durandoak ethernet adapter being configured.
718  GXT 500 display adapter (Magenta)
71c  340 MB SCSI disk drive (Sandalfoot - Conner) being configured.
720  Unknown Read/Write optical drive being identified/configured.
721  Unknown Disk being identified/configured.
721  Unknown SCSI device being identified/configured.
722  Unknown Disk being identified/configured.
723  Unknown CDROM being identified/configured.
724  Unknown Tape being identified/configured.
725  Unknown Display being identified/configured.
726  Unknown Input device being identified/configured.
727  Unknown Async device being identified/configured.
728  Parallel Printer being identified/configured.
729  Unknown Parallel device being identified/configured.
72c  540 MB SCSI disk drive (Sandalfoot - Maxtor) being configured.
730  Unknown diskette drive type being identified/configured.
731  PTY being identified/configured.
732  Unknown SCSI initiator type being configured.
733  Timberwolf 7GB 8mm tape drive being configured.
734  Nueces 4x SCSI-2 640MB CD-ROM Drive
735  Satsuma 540 MB SCSD SCSI disk drive being configured.
736  Quiet Touch keyboard and speaker cable being configured.
736  PS/2 Woodfield keyboard being configured.
737  Woodfield 540 MB SCSI Disk being configured.
738  Woodfield 810 MB SCSI disk being configured.
739  Woodfield CDROM drive being configured.
73c  540 MB SCSI disk drive (Sandalfoot - Quantum) being configured.
740  Pegasus 540 MB SCSI disk drive being configured.
741  Pegasus 1080 MB SCSI disk drive being configured.
742  Klickitat PCI Ethernet adapter being configured.
743  IsoFDDI adapter being identified/configured.
744  Carrera Power Management chip being configured.
745  Andante Tape Autoloader 16GB 4mm being configured.
746  SCSI-2 FW PCI Adapter being configured.
747  SCSI-2 Differential FW PCI Adapter being configured.
748  MCA/CHRP systems keyboard/mouse adapter being configured.
749  Timberwolf 7331-205 Tape library being configured
74c  ISA bus Token Ring Adapter (Sandalfoot) being configured.
750  Skyline Token Ring adapter being configured.
751  Copperhead SCSI 32-bit SE F/W RAID Adapter being configured.
752  OEM IDE Disk Drive being configured.
753  OEM IDE CD ROM Drive being configured.
754  1.1GB 16-bit SCSI disk drive being configured
755  2.2GB 16-bit SCSI disk drive being configured
756  4.5GB 16-bit SCSI disk drive being configured
757  Telemark External 13GB 1.5M/s 1/4 inch tape drive being configured
758  Aladdin 540 MB SCSI Drive being configured.
759  PC Co. Pegasus 1080 MB SCSI disk being configured.
75c  ISA bus Ethernet Adapter (Sandalfoot) being configured.
760  SCSI adapter function of LSA card being configured.
761  Ethernet adapter function of LSA card being configured.
762  SP: Configuration is running for the TB3 SP switch adapter card
763  SP Switch TB3 MX Adapter being configured.
764  SP System Attachment Adapter TB3 being configured.
765  Reserved - PowerParallel system MCA adapter
766  Reserved - PowerParallel system MCA adapter
767  Reserved - PowerParallel system Hi performance Switch (HPS)
768  Reserved - PowerParallel system HPS
769  Reserved - PowerParallel system HPS
76c  Sandalfoot 730 MB Satsuma SCSI drive being configured.
770  Reserved - PowerParallel system HPS
771  Reserved - PowerParallel system HPS
772  4.5GB SCSI F/W Disk Drive
773  9.1GB SCSI F/W Disk Drive
774  9.1GB External SCSI Disk Drive being configured.
775  Cobalt Graphics adapter being configured.
776  PCI Token-Ring Adapter Cricketstick being identified/configured.
777  Phoenix 10/100 Ethernet Tx PCI Adapter being identified or configured.
778  Sierra GXT3000P 3D PCI Graphics adapter being configured.
779  Mercury 3D PCI Graphics Adapter
77a  Enhanced Mirage (GXT2200P) FFC=2824 being configured
77b  Clover 4-port 10/100 Ethernet Adapter being configured
77c  1GB 16-bit SCSI disk drive being identified/configured.
780  C1X ISA X25 Adapter
781  Gale SDLC ISA Adapter
782  Quantum Fireball 1.2GB hardfile being configured.
783  Hidalgo 4mm DDS-2 Tape Autoloader being configured.
784  Orion 2160 MB SCSI Disk drive being configured.
785  San Gabriel ISA 8 Port EIA 232/RS 422 Adapter
786  GXT250P/GXT255P(Skyblue) graphic adapters being configured.
787  GXT500P/GXT550P (Mint) graphics adapter being configured.
788  Stream Video Capture card being configured.
789  Brewster 2.6GB External Optical Drive being configured
78B  Sonora Lite GXT4000P PCI Graphics Adapter being configured.
78C  PCI bus configuration executing.
78D  GXT300P 2D Graphics adapter being configured.
790  Multi-bus Integrated Ethernet Adapter being identified/configured.
791  Blanco 2.2 GB SCSI Disk Drive being Configured
792  Blanco 4.5 GB SCSI Disk Drive being Configured
793  Blanco 9.1 GB SCSI Disk Drive being Configured
794  San Remo  100 Mbps MCA Ethernet adapter being configured.
795  Honeycomb PCI FDDI adapter being configured.
796  Honeycomb MCA FDDI adapter being configured.
797  Turboways 155 UTP/STP ATM Adapter being identified/configured
798  Turboway 155 MPEG ATM adapter being configured.
798  Video streamer being identified or configured
799  Hermosa 2-Port Multiprotocol PCI adapter being identified/configured.
79c  ISA bus configuration executing.
7C0  CPU/System Interface being configured.
7C1  Business Audio Subsystem being identified/configured.
7c2  Starfire 1.1 GB 16B SCSI SE Disk drive with Allthorn Carrier
7c3  Sandalfoot Spitfire 1 GB 8B SCSI SE disk drive being configured.
7c4  Starfire 2.2 GB 16B SE disk drive with Allthorn carrier.
7c5  Presto 810 MB SCSI Disk being configured.
7c6  Starfire 4.4 GB 16B SE disk drive with Allthorn carrier.
7c7  Woodfield display device driver being configured
7c8  Woodfield video capture/playback device driver being configured.
7c9  Presto 1.2 GB SCSI Disk being configured.
7cc  PCMCIA bus configuration executing.
800  Turboways 155 MMF ATM Adapter being identified/configured
801  Reserved (Diagnostics)
802  Reserved (Diagnostics)
803  7336 Tape Library Robotics being configured
804  ASPEN 8x CDROM Drive SCSI-2 being configured
806  GXT800 (Supermint) PCI Graphics adapter being configured.
807  SCSI Device Enclosure being configured.
808  Pegasus SIF (System Interface Full) configuration process
809  Reserved (Diagnostics)
80c  Mayflower SSA 4-Port Adapter being indentified or configured
810  Reserved (Diagnostics)
811  Processor Complex being identified/configured.
812  Memory being identified or configured.
813  Battery for time-of-day, NVRAM, and so on being identified/ configured, or
     system I/O Control Logic being identified/ configured.
814  NVRAM being identified/configured.
815  Floating Point Processor being identified/configured.
816  Operator Panel Logic being identified/configured.
817  Time of Day Logic being identified/configured.
818  Reserved (diagnostics)
819  Graphics Input Device Adapter being identified/configured.
81c  S3 928 PCI graphics adapter being configured.
820  Interprocessor related testing
821  Standard Keyboard adapter being identified/configured.
823  Standard Mouse adapter being identified/configured.
824  Standard Tablet adapter being identified/configured.
825  Standard Speaker adapter being identified/configured.
826  Serial Port 1 adapter being identified/configured.
827  Parallel port adapter being identified/configured.
828  Standard Diskette Adapter being identified/configured.
829  Lumbee PCI ATM adapter being configured.
82c  Weitek P9000 PCI graphics adapter being configured.
830  Creek 8-Port ISA Async Adapter
831  IBM3151 adapter being identified or configured, or Serial Port 2
     being identified or configured.
832  Reserved (Diagnostics)
833  Reserved (Diagnostics)
834  64-Port Async Controller being identified/configured.
835  16-Port Async Concentrator being identified/configured.
836  128-Port Asynchronous Controller
837  16-port RAN, 16-EIA-232 being identified or configured.
838  Bitternut Network Terminal Accelerator adapter being identified/configured.
839  Bitternut 7318 Serial Communication Server being configured.
83c     SP2 High Performance Switch (HPS) being configured.
840  PCI Single-Ended Ultra SCSI Adapter being configured.
841  8-Port Async Adapter (EIA-232) being identified/configured.
842  8-Port Async Adapter (EIA-422A) being identified/configured.
843  8-Port Async Adapter (MIL-STD 188) being identified/configured.
844  Allthorn 7135 RAIDiant Array disk drive subsystem drawer being identified
845  7135 RAIDiant Array disk drive subsystem drawer being identified or
     configured.
846  RAIDiant Array SCSI 1.3GB Disk Drive
847  16-Port Serial Adapter (EIA-232) being identified/configured.
848  16-Port Serial Adapter (EIA-422) being identified/configured.
849  X.25 Communications Adapter being identified/configured.
84c  Slimline CD ROM Drive (Sandalfoot) being configured.
850  Token-Ring Network adapter being identified/configured.
851  T1/J1 Portmaster adapter being identified or configured.
852  Ethernet adapter being identified/configured.
853  SCSI D I/O controller being identified/configured.
854  3270 Connection being identified/configured.
855  4-port multiprotocol adapter being identified or configured.
856  POWER RADIANT device driver being configured
857  FSLA adapter being identified/configured.
858  5085/86/88 adapter being identified/configured.
859  FDDI adapter being identified/configured.
85c  Wildwood Token-Ring High-Performance LAN adapter being identfied/configured.
860  Twin Tail adapter being identified/configured.
861  Optical adapter being identified/configured.
862  Block multiplexer channel adapter being identified/configured.
863  MAP adapter being configured.
864  Serial Channel adapter being identified/configured.
865  370 Serial Channel adapter being identified/configured
866  SCSI Adapter being identified/configured.
867  Async Expansion adapter being identified/configured.
868  SCSI Adapter being identified/configured.
869  SCSI Adapter being identified/configured.
86c  270 MB SCSI disk drive (Sandalfoot - Quantum) being configured.
870  Serial Disk Drive  Adapter being identified/configured.
871  Graphics Subsystem Adapter being identified/configured.
872  Grayscale Graphics adapter being identified/configured.
873  Skyway 16 adapter being identified/configured.
874  Color Graphics adapter being identified/configured.
875  Vendor generic type communication adapter being configured.
876  8-Bit Color Graphics Processor being identified/configured.
877  POWER Gt3/Gt4 being identified or configured.
878  GT4 Graphics adapter being identified/configured.
879  24-bit Color Graphics Processor MEV2 being identified/configured
87c  360 MB SCSI disk drive (Sandalfoot - Satsuma 2) being configured.
880  POWER Gt1 graphics adapter being identified/configured.
881  Channel Attached Printer Adapter
882  Serial Attached Printer Adapter
883  Japan Pegasus support.
884  3117 Scanner Adapter
885  3118 Scanner Adapter
886  3119 Scanner Adapter
887  Integrated ethernet adapter being identified/configured.
888  Reserved
889  SCSI adapter being identified or configured.
88c  540 MB SCSI disk drive (Sandalfoot - Satsuma 3) being configured.
890  Corvette SCSI-2 DE/FW and SE/FW adapter being configured.
891  Vendor SCSI adapter being identified/configured.
892  Vendor Display adapter being identified/configured.
893  Vendor LAN adapter being identified/configured.
894  Vendor Async/Communications adapter being identified/configured.
895  Vendor IEEE 488 adapter being identified/configured.
896  Vendor VME Bus adapter being identified/configured.
897  S/370 Channel Emulator Adapter being identified or configured.
898  White Oak GT1X graphics adapter being identified or configured
899  Yuma/Calva 3490 attached tape drive being identified or configured
89c  Bandera multimedia SCSI CD-ROM is being identfied/configured.
8c0  Coral chip IDE ports being configured.
8c1  Exabyte 2502 IDE tape drive being configured.
8c2  IDE CD-ROM XA 2x being configured.
8c3  270 MB IDE disk drive being configured.
8c4  360 MB IDE disk drive being configured.
8c5  540 MB IDE disk drive being configured.
8c6  720 MB IDE disk drive being configured.
8c7  1 GB IDE disk drive being configured.
8cc  WDC AC1270F 270 MB IDE disk being configured
900  Brushy GXT110P Graphics Adapter being identified/configured.
901  Vendor SCSI device being identified/configured.
902  Vendor Display being identified/configured.
903  Vendor Async device being identified/configured.
904  Vendor Parallel device being identified/configured.
905  Vendor other adapter type being configured.
906  IBM Premier Speech Recognition adapter I being configured.
907  IBM Premier Speech Recognition adapter II being configured.
908  Ruby GXT1000 graphics subsystem being identified/configured
909  PEGASUS LSA (LAN SCSI/ADAPTER) being configured.
90c  DALA-3420 420 MB IDE disk being configured.
910  1/4GB Fibre Channel/266 Standard Adapter being indetified or configured
911  Fibre/Channel/1063 Adapter Short Wave.
912  2GB SCSI-2 differential tape drive being identified/configured
913  1GB SCSI-2 differential tape drive being identified/configured
914  5GB 8mm differential tape drive being identified/configured
915  Rhapsody 4GB 4mm SCSI Tape drive being identified/configured.
916  Non-SCSI vendor tape adapter being identified or configured
917  2.4GB 16-bit DE SCSI disk drive being identified/configured
918  2.4GB 16-bit SE SCSI disk drive being identified/configured
919  Multimedia Audio adapter being identified/configured.
91c  Sandalfoot 4mm 2GB tape drive being configured.
920  Bridge box being identified or configured
921  Keyboard 101 being identified/configured.
922  Keyboard 102 being identified/configured.
923  Keyboard Kanji being identified/configured.
924  2-Button Mouse being identified/configured.
925  3-Button Mouse being identified/configured.
926  Tablet 5083 Model 21 being identified/configured.
927  Tablet 5083 Model 22 being identified or configured
928  Standard speaker being identified or configured
929  Dials being identified or configured
930  Lighted Program Function Keys(LPFK) being identified or
     configured
927  Tablet 5083 Model 22 being identified/configured.
928  Standard Speaker being identified/configured.
929  Dials being identified/configured.
92c  DALA-3540 540 MB IDE disk being configured.
930  Lighted Program Function Keys (LPF) keyboard being
931  IP router being identified or configured
933  Async Planar being identified/configured.
934  Async Expansion Drawer being identified/configured.
935  2 MB 3.5-Inch Diskette Drive being identified/configured.
936  5.25-Inch Diskette drive being identified/configured.
937  HIPPI adapter (Torch) being configured.
938  (Yukon) Serial HIPPI PCI adapter being configured.
939  Reserved (Diagnostics)
93c  DPEA-30540 540 MB IDE disk being configured.
940  Reserved ( Diagnostics)
942  Baby Blue GXT100 graphics adapter being identified/configured
943  3480 and 3490 control units attached to a System/370 Channel Emulator/A
      adapter are identified/configured.
944  100MB ATM adapter being configured
945  Spitfire 1 GB 16 Bit DE drive being identified/configured.
946  Serial port 3 adapter is being identified or configured.
947  Satsuma730MB SCSI disk drive is being configured.
948  Portable disk drive being identified or configured
949  Unknown Bus Attached Disk Drive being identified/configured.
94c  WDC AC2540H 540 MB IDE disk being configured.
950  Missing SCSI device being identified or configured
951  670 MB SCSI Disk Drive being identified/configured.
952  355 MB SCSI Disk Drive being identified/configured.
953  320 MB SCSI Disk Drive being identified/configured.
954  400 MB SCSI Disk Drive being identified/configured.
955  857 MB SCSI Disk Drive being identified/configured.
956  670 MB SCSI Disk Drive being identified/configured.
957  120 MB Direct Bus Attached Disk Drive being identified/configured.
958  160 MB Direct Bus Attached Disk Drive being identified/configured.
959  160 MB SCSI Disk Drive being identified/configured.
95c  WDC AC2700H 730 MB IDE disk being configured.
960  1.37GB SCSI disk drive being identified/configured.
961  Route 66 2 Port Serial Adapter being configured.
962  Route 66 Ethernet Adapter being configured.
964  Mammoth 20 GB 8mm tape drive being configured
965  Route 66 Token Ring Adapter being configured.
966  Digital to Analog Video Decoder Adapter being configured.
967  Peermaster (Xpoint) Ethernet adapter being configured.
968  1.0GB 3.5" SCSI disk drive being identified or configured.
969  Reserved (Diagnostics)
96c  DPEA-30810 810 MB IDE disk being configured.
970  0.5-Inch 9-Track Tape drive being identified/configured.
971  150 MB .25-Inch Tape drive being identified/configured.
972  8mm SCSI Tape drive being identified/configured.
973  Other SCSI Tape drive being identified/configured.
974  CDROM drive being identified/configured.
975  ERIMO optical disk drive is being identified/configured.
976  RISC System/6000 SCSI I/O Controller Initiator
977  M-Audio capture and playback adapter being identified/configured.
978  IEEE 4888 Adapter being identified/configured.
979  7246 SBS Frame Buffer Adapter being configured.
97c  DPEA-301080 1080 MB IDE disk drive being configured.
980  TBO - IBM Switching network interface adapter being configured.
981  540MB SCSI-2 disk drive being identified or configured.
982  Graphics Visualization Server Adapter
983  XGA grapphics adapter being identified/configured.
984  1GB 8-bit disk drive being identified/configured.
985  M-Video capture and playback adapter being identified or configured.
986  2.4 GB SCSI Disk Drive being identified/configured.
987  Enhanced SCSI CD-ROM drive is being identified/configured.
988  KILLY FDDI adapter being configured.
989  200 MB SCSI Disk Drive being identified/configured.
98c  WDC AC31000H 1083 MB IDE disk being configured.
990  2.0 GB SCSI Disk Drive being identified/configured.
991  525 MB 1/4 inch SCSI Tape being identified/configured.
992  4755 Crytographic adapter being configured.
993  Raven File Server product being configured.
994  5 GB 8mm Tape Drive being identified/configured
995  1.2GB 1/4-Inch tape drive being identified/configured.
996  MP/A adapter being configured.
997  Twisted pair FDDI adapter being identify/configured.
998  2GB 4mm tape drive being identified/configured.
999  7137 or 3514 Disk Array Subsystem being identified/configured
99c  2 GB SCSI Disk drive being configured.
D46  Token-Ring Cable
D50  SCSI Device/SCSI Cable/SCSI Terminator
D81  T2 Ethernet Adapter II being configured
2530  10/100 Mbps Ethernet PCI Adapter being configured

   ___________________________________________________________________________
  |   Valid Power Failure Codes    |                                          |
  |________________________________|             Type of Failure              |
  | Digit 1  | Digit 2  | Digit 3  |                                          |
  |__________|__________|__________|__________________________________________|
  |  blank   |  blank   |  blank   | No                                       |
  |    8     |          |          | Fan P49B.                                |
  |    4     |          |          | Fan P49C.                                |
  |    u     |          |          | = Digit 1 Codes 8 and 4.                 |
  |          |    8     |          | Fan at P47.                              |
  |          |    4     |          | Fan P46A or P46 or both.                 |
  |          |    2     |          | Fan P49A.                                |
  |          |    6     |          | = Digit 2 Codes 4 and 2.                 |
  |          |    c     |          | = Digit 2 codes 8 and 2.                 |
  |          |    u     |          | = Digit 2 codes 8 and 4.                 |
  |          |Inverted F|          | = Digit 2 codes 8, 4 and 2.              |
  |          |          |    8     |  Excessive temperature in power supply.  |
  |          |          |    4     |  Power failure in power supply.          |
  |          |          |    2     |  Power failure outside power supply.     |
  |          |          |    1     |  Loss of primary power.                  |
  |__________|__________|__________|__________________________________________|

CHRP Version 3 logs ELA Source Numbers

A00 - A1F CHRP Version 3 ELA
A20 - AFF Reserved

Diagnostics Load Progress Indicators

c00     AIX Install/Maintenance loaded successfully.
c01     Insert the first diagnostic diskette.
c02     Diskettes inserted out of sequence.
c03     The wrong diskette is in diskette drive.
c04     The loading stopped with a nonrecoverable error.
c05     A diskette error occurred.
c06     The rc.boot configuration shell script is unable to determine
        type of boot.
c07     Insert the next diagnostic diskette.
c08     RAM file system started incorrectly.
c09     The diskette drive is reading or writing a diskette.

Kernel Debugger Codes

c20     An unexpected halt occurred, and the system is configured to enter
        the kernel debug program instead of entering a system dump.

Boot and Install Codes

c21     The ifconfig command was unable to configure the network
        for the client network host.
c22     The tftp command was unable to read client's
        ClientHostName info file during a client network boot.
c24     Unable to read client's ClientHostName.info
        file during a client network boot.
c25     Client did not mount remote miniroot during network install.
c26     Client did not mount the /usr file system during the network boot.
c29     The system was unable to configure the network device.

Console

c31     Select the console display for the diagnostics. To select No console
        display, set the key mode switch to Normal then to Service. The
        diagnostic programs will then load and run the diagnostics
        automatically.
c32     A direct-attached display (HFT/LFT) was selected.
c33     A tty terminal attached to serial ports S1 or S2 was selected.
c34     A file was selected. The console messages store in a file.

BOS Install Codes

c40     Configuration files are being restored.
c41     Could not determine the boot type or device.
c42     Extracting data files from diskette.
c43     Cannot access the boot/install tape.
c44     Initializing installation database with target disk information.
c45     Cannot configure the console.
c46     Normal installation processing.
c47     Could not create a physical volume identifier (PVID) on disk.
c48     Prompting you for input.
c49     Could not create or form the JFS log.
c50     Creating root volume group on target disks.
c51     No paging devices were found.
c52     Changing from RAM environment to disk environment.
c53     Not enough space in the /tmp directory to do a preservation installation.
c54     Installing either BOS or additional packages.
c55     Could not remove the specified logical volume in a preservation installation.
c56     Running user-defined customization.
c57     Failure to restore BOS.
c58     Displaying message to turn the key.
c59     Could not copy either device special files, device ODM, or volume
        group information from RAM to disk.
c61     Failed to create the boot image.
c62     Loading platform dependent debug files.
c63     Loading platform dependent data files
c64     Failed to load platform dependent data files

Diagnostic Codes

c70     Problem Mounting diagnostic CDROM disc
c99     Diagnostics have completed. This code is only used when there is
        no console.
Fxx     Fxx, (xx is any character) - Victory Firmware usage.